Land clearing, dirt work and excavating from Abilene to WeatherfordLand clearing and dirt work around Ranger
Hughes Dirt Service
Land clearing in Comanche, TX
Call (254) 210-2570 Request a Quote

How Much Does a Gravel Driveway Cost in Texas?

One national cost guide puts an installed gravel driveway at $4 to $10 a square foot. Another puts most driveways at $500 to $3,500, with a $1,800 national average. The rock alone sells for about $10 to $50 a ton.

These are market numbers, not our price list. They show what moves the price, so a written quote makes sense when you get one. Our page on gravel driveways in the Ranger area covers how we build and regrade them.

What does a gravel driveway cost per square foot?

Length and width move the total more than anything else, one national guide says. The national cost guides publish these 2026 ranges.

What you pay forPublished range
Installed driveway, rock and labor$4 to $10 per sq ft in one guide; $500 to $3,500 a job in another
Rock only$10 to $50 per ton, $15 to $75 per cubic yard, or $1 to $3 per sq ft laid 12 inches deep
Delivery$10 to $25 per ton, or $100 to $500 per load
Truckload, delivered and spread$1,350 and up, 10 cubic yard minimum
Grading the base$1 to $3 per sq ft
Culvert or drain, where one is needed$500 to $2,000
Yearly upkeep$100 to $400

One national guide prices a double-car driveway of 400 to 600 square feet at $800 to $2,200. Its long rural drive, about 2,000 square feet, runs $3,500 to $6,000 and up. At that published range, the long drive works out to about $1.75 to $3 or more a square foot.

A driveway on ranch land can run hundreds of feet. At the same published range, a 12-foot-wide lane works out to about $2,100 to $3,600 or more per 100 feet.

What does each kind of rock cost per ton?

One national guide names the type of rock as the main driver of material cost. The Texas Department of Transportation (TxDOT) calls road base flexible base. Its 2024 spec lists crushed stone, gravel, crushed concrete and caliche among the base types.

RockWhat it isPublished price per ton
Crushed limestoneQuarried stone crushed into angular pieces$30 to $40
Road baseCrushed rock and fines that lock together when packed$18 to $31
CalicheA base rock TxDOT lists as its Type E$30 to $100
Crushed concreteOld concrete, crushed and reused; TxDOT’s Type D$11 to $53

Caliche shows the widest spread. One national guide notes the word can also mean decorative rock. Ask what a caliche price covers before you compare quotes.

How much rock does a driveway take?

Depth decides the tonnage. One national guide calls for at least 4 to 6 inches of rock. Another puts the minimum at 5 to 6 inches for cars, and 8 to 12 where trucks and RVs run. A driveway that takes loaded stock trailers is closer to that heavier case.

At 4 inches, a ton of gravel covers about 60 to 80 square feet, by one guide’s rule of thumb. A 10 by 100 foot driveway takes about 13 to 17 tons at that depth. At 8 inches, the same driveway takes about 33 tons. Order 10 to 15 percent extra for settling and spillage.

A 10-wheel dump truck hauls about 12 to 20 tons. At those published figures, a 1,000 square foot driveway at 4 inches works out to about one truckload. Distance adds up on rural land. One guide adds about $10 for each mile past the first five.

Why do base prep and drainage change the price?

The lane is cleared and shaped before any rock goes down. National guides price grading at $1 to $3 a square foot, or $1,000 to $3,000 a driveway. Clearing brush or trees off the route adds $500 to $2,000 in one guide. Rough terrain raises labor 20 to 50 percent in another.

If the route runs through mesquite and cedar, land clearing comes first. If you are building, the driveway and the house pad can be planned as one job.

The Federal Highway Administration’s gravel roads guide says problems develop quickly when a gravel surface has no crown. It recommends about half an inch of crown per foot, roughly 4 percent, and no more than 6 percent. Without a crown, water collects on top and softens the surface. Ruts can follow, down into the ground below.

Texas law bars diverting natural runoff in a way that damages another owner’s property. Ditches along a new driveway should carry water the way it already ran.

Do you need a permit for a gravel driveway in Texas?

The road your driveway meets decides who to ask. For a driveway onto a state highway, TxDOT’s local district office handles the permit, Form 1058. Work in the right of way waits for the signed permit and 24 hours’ notice to TxDOT.

County roads follow county rules. Taylor County, for one, charges $25 for a driveway permit and calls for a culvert at least 30 feet long. Eastland County’s site posts no driveway permit, so ask the county commissioner for your area.

Inside city limits, the city answers. Brownwood and Stephenville both list driveways among the work that needs a city permit. One national guide puts city permits at $50 to $300.

Texas law also requires a call to 811 at least two business days before most digging 16 inches or deeper. We point you to the right office before work starts.

What does it cost to regrade an old gravel driveway?

A worn driveway can often be regraded instead of rebuilt. Regrading pulls the rock that traffic pushed to the edges back onto the surface. It rebuilds the crown and fills the potholes. Fresh rock goes where the old layer wore thin.

One national guide puts yearly upkeep at $100 to $400 for regrading and fresh gravel. A full rebuild, with the old gravel out and the base redone, runs $1,500 to $6,000. Deep ruts and a failing base point toward the rebuild, the same guide says.

The rock matters on a regrade too. Federal guidance says surface gravel needs enough fines to bind together. Base rock with few fines will not form a crust on top.

A lane that crosses a whole ranch is closer to a road than a driveway. That is gravel road construction, with the roadbed cut and crowned so water sheds.

How do you get a real number for your driveway?

Start with the size of the driveway and what will drive on it. Note where water runs in a hard rain and which road the driveway meets.

Hughes Dirt Service is based in Ranger, and our service area runs about 60 miles around Ranger. We look at the job and put the quote in writing. Call or text (254) 210-2570, or read more about how we build gravel driveways.

Frequently asked questions

How much does a gravel driveway cost per square foot?
One national cost guide puts an installed gravel driveway at $4 to $10 a square foot. Another prices a long rural drive of about 2,000 square feet at $3,500 to $6,000 and up. At that published range, that drive works out to about $1.75 to $3 or more a square foot.
How much does a truckload of gravel cost?
One national guide prices a truckload, delivered and spread, at $1,350 and up. Another puts hauling alone at $100 to $500 a load, by distance. A 10-wheel dump truck carries about 12 to 20 tons.
Is caliche good for a gravel driveway?
TxDOT lists caliche as a base type in its 2024 road base spec. One national guide prices it at $30 to $100 a ton, and another at $45 to $100. Ask what a caliche price covers, since the word can also mean decorative rock.
How deep should a gravel driveway be?
One national guide calls for at least 4 to 6 inches of rock. Another puts the minimum at 5 to 6 inches for cars, and 8 to 12 where trucks and RVs run. Each extra inch means more tons, so depth moves the price.
What does it cost to regrade a gravel driveway?
One national guide puts yearly upkeep at $100 to $400, for work like regrading and fresh gravel. A full rebuild with the base redone runs $1,500 to $6,000. Deep ruts and a failing base point toward the rebuild.
Do I need a permit for a gravel driveway in Texas?
It depends on the road the driveway meets. A driveway onto a state highway goes through TxDOT's local district office. County roads follow county rules, and inside city limits the city answers. We point you to the right office before work starts.
Is this what Hughes Dirt Service charges?
No. These are market numbers from national cost guides and public sources, not our price list. We look at the job and put the quote in writing. Call or text (254) 210-2570.
Request a Quote

Get In Touch With Hughes Dirt Service

Tell us what the job is and the town it is near, and text us photos if you have them. Call or text (254) 210-2570, or send the form and we will get back to you.

  • Call or text (254) 210-2570
  • Serving Ranger, TX and the towns from Abilene to Weatherford
  • Written quotes · land clearing, dirt work and excavating

Request a Quote

Tell us about the clearing, tank, pad, driveway or teardown and where it is. We look at the job and put the quote in writing.

Call (254) 210-2570